A parametric study for the design of an optimized ultrasonic percussive planetary drill tool
A parametric study for the design of an optimized ultrasonic percussive planetary drill tool
Traditional rotary drilling for planetary rock sampling, in situ analysis, and sample return are challenging because the axial force and holding torque requirements are not necessarily compatible with lightweight spacecraft architectures in low-gravity environments. This paper seeks to optimize an ultrasonic percussive drill tool to achieve rock penetration with lower reacted force requirements, with a strategic view toward building an ultrasonic planetary core drill (UPCD) device. The UPCD is a descendant of the ultrasonic/sonic driller/corer technique. In these concepts, a transducer and horn (typically resonant at around 20 kHz) are used to excite a toroidal free mass that oscillates chaotically between the horn tip and drill base at lower frequencies (generally between 10 Hz and 1 kHz). This creates a series of stress pulses that is transferred through the drill bit to the rock surface, and while the stress at the drill-bit tip/rock interface exceeds the compressive strength of the rock, it causes fractures that result in fragmentation of the rock. This facilitates augering and downward progress. In order to ensure that the drill-bit tip delivers the greatest effective impulse (the time integral of the drill-bit tip/rock pressure curve exceeding the strength of the rock), parameters such as the spring rates and the mass of the free mass, the drill bit and transducer have been varied and compared in both computer simulation and practical experiment. The most interesting findings and those of particular relevance to deep drilling indicate that increasing the mass of the drill bit has a limited (or even positive) influence on the rate of effective impulse delivered.
577 - 589
Li, Xuan
ed01c0d5-68e0-4abe-8642-5b9ebf153314
Harkness, Patrick
f9a62f8c-1950-427e-82ee-ebfc3576feb3
Worrall, Kevin
8e62cf60-ce38-41e8-a71e-71fc754fa6fb
Timoney, Ryan
6237de68-9352-46b5-a954-8e8a36d8f4e6
Lucas, Margaret
8f1502b9-ffaa-4cb6-b78c-a1b58e1d31b2
29 November 2016
Li, Xuan
ed01c0d5-68e0-4abe-8642-5b9ebf153314
Harkness, Patrick
f9a62f8c-1950-427e-82ee-ebfc3576feb3
Worrall, Kevin
8e62cf60-ce38-41e8-a71e-71fc754fa6fb
Timoney, Ryan
6237de68-9352-46b5-a954-8e8a36d8f4e6
Lucas, Margaret
8f1502b9-ffaa-4cb6-b78c-a1b58e1d31b2
Li, Xuan, Harkness, Patrick, Worrall, Kevin, Timoney, Ryan and Lucas, Margaret
(2016)
A parametric study for the design of an optimized ultrasonic percussive planetary drill tool.
IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, 64 (3), .
(doi:10.1109/TUFFC.2016.2633319).
Abstract
Traditional rotary drilling for planetary rock sampling, in situ analysis, and sample return are challenging because the axial force and holding torque requirements are not necessarily compatible with lightweight spacecraft architectures in low-gravity environments. This paper seeks to optimize an ultrasonic percussive drill tool to achieve rock penetration with lower reacted force requirements, with a strategic view toward building an ultrasonic planetary core drill (UPCD) device. The UPCD is a descendant of the ultrasonic/sonic driller/corer technique. In these concepts, a transducer and horn (typically resonant at around 20 kHz) are used to excite a toroidal free mass that oscillates chaotically between the horn tip and drill base at lower frequencies (generally between 10 Hz and 1 kHz). This creates a series of stress pulses that is transferred through the drill bit to the rock surface, and while the stress at the drill-bit tip/rock interface exceeds the compressive strength of the rock, it causes fractures that result in fragmentation of the rock. This facilitates augering and downward progress. In order to ensure that the drill-bit tip delivers the greatest effective impulse (the time integral of the drill-bit tip/rock pressure curve exceeding the strength of the rock), parameters such as the spring rates and the mass of the free mass, the drill bit and transducer have been varied and compared in both computer simulation and practical experiment. The most interesting findings and those of particular relevance to deep drilling indicate that increasing the mass of the drill bit has a limited (or even positive) influence on the rate of effective impulse delivered.
This record has no associated files available for download.
More information
Published date: 29 November 2016
Identifiers
Local EPrints ID: 497560
URI: http://eprints.soton.ac.uk/id/eprint/497560
ISSN: 0885-3010
PURE UUID: 3e5efc2c-6c5b-410d-83d2-3c133280f67f
Catalogue record
Date deposited: 27 Jan 2025 17:58
Last modified: 28 Jan 2025 03:15
Export record
Altmetrics
Contributors
Author:
Xuan Li
Author:
Patrick Harkness
Author:
Kevin Worrall
Author:
Ryan Timoney
Author:
Margaret Lucas
Download statistics
Downloads from ePrints over the past year. Other digital versions may also be available to download e.g. from the publisher's website.
View more statistics