The University of Southampton
University of Southampton Institutional Repository

The investigation of the energy harvesting performance using electrospun PTFE/PVDF based on a triboelectric assembly

The investigation of the energy harvesting performance using electrospun PTFE/PVDF based on a triboelectric assembly
The investigation of the energy harvesting performance using electrospun PTFE/PVDF based on a triboelectric assembly
This work presents an investigation into the energy harvesting performance of a combination of polytetrafluoroethylene (PTFE) and polyvinylidene fluoride (PVDF) materials prepared using a one-step electrospinning technique. Before electrospinning, different percentages of the 1 micron PTFE powder were added to a PVDF precursor. The surface morphology of the electrospun PTFE/PVDF fibre was investigated using a scanning electron microscope and tunnelling electron microscope. The structure was investigated using Fourier-transform infrared spectroscopy and x-ray diffraction analysis (XRD). A highly porous structure was observed with a mix of the α- and β-phase PVDF. The amount of β-phase was found to reduce when increasing the percentage of PTFE. The maximum amount of PTFE that could be added and still be successfully electrospun was 20%. This percentage showed the highest energy harvesting performance of the different PTFE/PVDF combinations. Electrospun fibres with different percentages of PTFE were deployed in a triboelectric energy harvester operating in the contact separation mode and the open circuit voltage and short circuit current were obtained at frequencies of 4–9 Hz. The 20% PTFE fibre showed 4 (51–202 V) and 7 times (1.3–9.04 µA) the voltage and current output respectively when compared with the 100% PVDF fibre. The Voc and Isc were measured for different load resistances from 1 kΩ to 6 GΩ and achieved a maximum power density of 348.5 mW m−2 with a 10 MΩ resistance. The energy stored in capacitors 0.1, 0.47, 1, and 10 µF from a book shaped PTFE/PVDF energy harvester were 1.0, 16.7, 41.2 and 136.8 µJ, respectively. The electrospun fibre is compatible with wearable and e-textile applications as it is breathable and flexible. The electrospun PTFE/PVDF was assembled into shoe insoles to demonstrate energy harvesting performance in a practical application.
0964-1726
White, Pattarinee
ef6aec5f-d14a-469b-bd91-51156aad9c0c
Pankaew, Piyapong
53d6495d-dddb-4b82-a9db-43ad67193fc5
Bavykin, Dmitry
1e9fabfc-d078-4585-876f-85ff33b7eed5
Moshrefi-Torbati, M.
65b351dc-7c2e-4a9a-83a4-df797973913b
Beeby, Stephen
ba565001-2812-4300-89f1-fe5a437ecb0d
White, Pattarinee
ef6aec5f-d14a-469b-bd91-51156aad9c0c
Pankaew, Piyapong
53d6495d-dddb-4b82-a9db-43ad67193fc5
Bavykin, Dmitry
1e9fabfc-d078-4585-876f-85ff33b7eed5
Moshrefi-Torbati, M.
65b351dc-7c2e-4a9a-83a4-df797973913b
Beeby, Stephen
ba565001-2812-4300-89f1-fe5a437ecb0d

White, Pattarinee, Pankaew, Piyapong, Bavykin, Dmitry, Moshrefi-Torbati, M. and Beeby, Stephen (2024) The investigation of the energy harvesting performance using electrospun PTFE/PVDF based on a triboelectric assembly. Smart Materials and Structures, 33 (7), [075010]. (doi:10.1088/1361-665X/ad508d).

Record type: Article

Abstract

This work presents an investigation into the energy harvesting performance of a combination of polytetrafluoroethylene (PTFE) and polyvinylidene fluoride (PVDF) materials prepared using a one-step electrospinning technique. Before electrospinning, different percentages of the 1 micron PTFE powder were added to a PVDF precursor. The surface morphology of the electrospun PTFE/PVDF fibre was investigated using a scanning electron microscope and tunnelling electron microscope. The structure was investigated using Fourier-transform infrared spectroscopy and x-ray diffraction analysis (XRD). A highly porous structure was observed with a mix of the α- and β-phase PVDF. The amount of β-phase was found to reduce when increasing the percentage of PTFE. The maximum amount of PTFE that could be added and still be successfully electrospun was 20%. This percentage showed the highest energy harvesting performance of the different PTFE/PVDF combinations. Electrospun fibres with different percentages of PTFE were deployed in a triboelectric energy harvester operating in the contact separation mode and the open circuit voltage and short circuit current were obtained at frequencies of 4–9 Hz. The 20% PTFE fibre showed 4 (51–202 V) and 7 times (1.3–9.04 µA) the voltage and current output respectively when compared with the 100% PVDF fibre. The Voc and Isc were measured for different load resistances from 1 kΩ to 6 GΩ and achieved a maximum power density of 348.5 mW m−2 with a 10 MΩ resistance. The energy stored in capacitors 0.1, 0.47, 1, and 10 µF from a book shaped PTFE/PVDF energy harvester were 1.0, 16.7, 41.2 and 136.8 µJ, respectively. The electrospun fibre is compatible with wearable and e-textile applications as it is breathable and flexible. The electrospun PTFE/PVDF was assembled into shoe insoles to demonstrate energy harvesting performance in a practical application.

Text
White_2024_Smart_Mater._Struct._33_075010 - Version of Record
Available under License Creative Commons Attribution.
Download (3MB)

More information

Accepted/In Press date: 24 May 2024
Published date: 6 June 2024

Identifiers

Local EPrints ID: 501727
URI: http://eprints.soton.ac.uk/id/eprint/501727
ISSN: 0964-1726
PURE UUID: f6c59592-86b0-4325-82a9-037beb73eb5e
ORCID for Pattarinee White: ORCID iD orcid.org/0000-0001-6341-6378
ORCID for Stephen Beeby: ORCID iD orcid.org/0000-0002-0800-1759

Catalogue record

Date deposited: 09 Jun 2025 17:25
Last modified: 22 Aug 2025 02:26

Export record

Altmetrics

Contributors

Author: Pattarinee White ORCID iD
Author: Piyapong Pankaew
Author: Dmitry Bavykin
Author: Stephen Beeby ORCID iD

Download statistics

Downloads from ePrints over the past year. Other digital versions may also be available to download e.g. from the publisher's website.

View more statistics

Atom RSS 1.0 RSS 2.0

Contact ePrints Soton: eprints@soton.ac.uk

ePrints Soton supports OAI 2.0 with a base URL of http://eprints.soton.ac.uk/cgi/oai2

This repository has been built using EPrints software, developed at the University of Southampton, but available to everyone to use.

We use cookies to ensure that we give you the best experience on our website. If you continue without changing your settings, we will assume that you are happy to receive cookies on the University of Southampton website.

×